/*
 * Copyright (c) 2016-2017, The Linux Foundation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 and
 * only version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

#include "msm8953-pinctrl.dtsi"
#include "msm8953-audio-mtp.dtsi"
#include "msm8953-camera-sensor-ipc.dtsi"

&spi_3 { /* BLSP1 QUP3 */
	spi-max-frequency = <16000000>;
	maxim_sti@0 {
		status = "disabled";
		compatible = "maxim,maxim_sti";
		reg = <0>;
		interrupt-parent = <&tlmm>;
		interrupts = <65 0>;
		spi-max-frequency = <16000000>;
		avdd-supply = <&pm8953_l10>;
		dvdd-supply = <&pm8953_l5>;
		maxim_sti,irq-gpio = <&tlmm 65 0x00>;
		maxim_sti,reset-gpio = <&tlmm 64 0x00>;
		maxim_sti,touch_fusion = "/vendor/bin/touch_fusion";
		maxim_sti,config_file = "/etc/firmware/qtc800s.cfg";
		maxim_sti,fw_name = "qtc800s.bin";
		pinctrl-names = "pmx_ts_active","pmx_ts_suspend",
						"pmx_ts_release";
		pinctrl-0 = <&ts_int_active &ts_reset_active>;
		pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
		pinctrl-2 = <&ts_release>;
	};
};

&i2c_5 { /* BLSP2 QUP1 (NFC) */
	nq@28 {
		compatible = "qcom,nq-nci";
		reg = <0x28>;
		qcom,nq-irq = <&tlmm 17 0x00>;
		qcom,nq-ven = <&tlmm 16 0x00>;
		qcom,nq-firm = <&tlmm 62 0x00>;
		qcom,nq-clkreq = <&pm8953_gpios 2 0x00>;
		interrupt-parent = <&tlmm>;
		qcom,clk-src = "BBCLK2";
		interrupts = <17 0>;
		interrupt-names = "nfc_irq";
		pinctrl-names = "nfc_active", "nfc_suspend";
		pinctrl-0 = <&nfc_int_active &nfc_disable_active>;
		pinctrl-1 = <&nfc_int_suspend &nfc_disable_suspend>;
		clocks = <&clock_gcc clk_bb_clk2_pin>;
		clock-names = "ref_clk";
	};
};

&pm8953_l10 {
	regulator-max-microvolt = <2850000>;
};

&soc {
	gpio_keys {
		compatible = "gpio-keys";
		input-name = "gpio-keys";
		pinctrl-names = "tlmm_gpio_key_active","tlmm_gpio_key_suspend";
		pinctrl-0 = <&gpio_key_active>;
		pinctrl-1 = <&gpio_key_suspend>;

		vol_up {
			label = "volume_up";
			gpios = <&tlmm 85 0x1>;
			linux,input-type = <1>;
			linux,code = <115>;
			debounce-interval = <15>;
		};
	};

	hbtp {
		compatible = "qcom,hbtp-input";
		vcc_ana-supply = <&pm8953_l10>;
		vcc_dig-supply = <&pm8953_l5>;
		qcom,afe-load = <50000>;
		qcom,afe-vtg-min = <2850000>;
		qcom,afe-vtg-max = <2850000>;
		qcom,dig-load = <15000>;
		qcom,dig-vtg-min = <1800000>;
		qcom,dig-vtg-max = <1800000>;
	};

	tlmm: pinctrl@1000000 {
		ssusb_mode_sel: ssusb_mode_sel {
			mux {
				pins = "gpio61";
				function = "gpio";
			};

			config {
				pins = "gpio61";
				drive-strength = <2>;
				bias-disable;
				input-enable;
			};
		};
	};

	usb_detect {
		compatible = "qcom,gpio-usbdetect";
		interrupt-names = "vbus_det_irq";
		interrupt-parent = <&tlmm>;
		interrupts = <61 0>;
		pinctrl-names = "default";
		pinctrl-0 = <&ssusb_mode_sel>;
		qcom,notify-host-mode;
		qcom,disable-device-mode;
		qcom,gpio-mode-sel = <&tlmm 61 0>;
	};

	dsi_panel_lt_pwr_supply: dsi_panel_lt_pwr_supply {
		#address-cells = <1>;
		#size-cells = <0>;

		qcom,panel-supply-entry@0 {
			reg = <0>;
			qcom,supply-name = "vdd";
			qcom,supply-min-voltage = <2850000>;
			qcom,supply-max-voltage = <2850000>;
			qcom,supply-enable-load = <100000>;
			qcom,supply-disable-load = <100>;
		};

		qcom,panel-supply-entry@1 {
			reg = <1>;
			qcom,supply-name = "vddio";
			qcom,supply-min-voltage = <1800000>;
			qcom,supply-max-voltage = <1800000>;
			qcom,supply-enable-load = <100000>;
			qcom,supply-disable-load = <100>;
		};
	};
};

&spmi_bus {
	qcom,pmi8950@2 {
		pmi8950_charger: qcom,qpnp-smbcharger {
			smbcharger_charger_otg: qcom,smbcharger-boost-otg {
				status = "disabled";
			};
		};
	};
};

&pmi_haptic{
	qcom,actuator-type = "lra";
	qcom,lra-auto-res-mode="qwd";
	qcom,lra-high-z="opt1";
	qcom,lra-res-cal-period = <0>;
	qcom,wave-play-rate-us = <4165>;
};

&wled {
	qcom,cons-sync-write-delay-us = <1000>;
};

&flash_led {
	compatible = "qcom,qpnp-flash-led";
	reg = <0xd300 0x100>;
	qcom,follow-otst2-rb-disabled;
};

#include "msm8953-mdss-panels.dtsi"

&i2c_5 { /* BLSP2 QUP1 (HDMI) */
	lt8912@48 {
		compatible = "lontium,lt8912";
		reg = <0x48>;
		qcom,hdmi-reset = <&tlmm 64 0x0>;
	};
};

&dsi_lt8912_1080_vid {
	qcom,mdss-dsi-panel-timings-phy-v2 = [23 1e 08 09 05 03 04 a0
		23 1e 08 09 05 03 04 a0
		23 1e 08 09 05 03 04 a0
		23 1e 08 09 05 03 04 a0
		23 1a 08 09 05 03 04 a0];

	qcom,panel-supply-entries = <&dsi_panel_lt_pwr_supply>;
};

&mdss_mdp {
	qcom,mdss-pref-prim-intf = "dsi";
};

&mdss_dsi {
	hw-config = "single_dsi";
};

&mdss_dsi0 {
	qcom,dsi-pref-prim-pan = <&dsi_lt8912_1080_vid>;
	pinctrl-names = "mdss_default", "mdss_sleep";
	pinctrl-0 = <&mdss_dsi_active &mdss_te_active>;
	pinctrl-1 = <&mdss_dsi_suspend &mdss_te_suspend>;

	qcom,pluggable;

	qcom,platform-te-gpio = <&tlmm 24 0>;
	qcom,platform-bklight-en-gpio = <&tlmm 59 0>;
};

&mdss_dsi1 {
	status = "disabled";
	qcom,dsi-pref-prim-pan = <&dsi_adv7533_1080p>;
	pinctrl-names = "mdss_default", "mdss_sleep";
	pinctrl-0 = <&mdss_dsi_active &mdss_te_active>;
	pinctrl-1 = <&mdss_dsi_suspend &mdss_te_suspend>;

	qcom,pluggable;
	qcom,platform-te-gpio = <&tlmm 24 0>;
	qcom,platform-bklight-en-gpio = <&tlmm 59 0>;
};

&labibb {
	status = "ok";
	qpnp,qpnp-labibb-mode = "lcd";
};

&dsi_truly_1080_vid {
	status = "disabled";
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,mdss-dsi-pan-enable-dynamic-fps;
	qcom,mdss-dsi-pan-fps-update = "dfps_immediate_clk_mode";
};

&dsi_truly_1080_cmd {
	status = "disabled";
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,ulps-enabled;
	qcom,partial-update-enabled;
	qcom,panel-roi-alignment = <2 2 4 2 1080 2>;
};

&blsp1_uart0 {
	status = "ok";
	pinctrl-names = "default";
	pinctrl-0 = <&uart_console_active>;
};

&sdhc_1 {
	/* device core power supply */
	vdd-supply = <&pm8953_l8>;
	qcom,vdd-voltage-level = <2900000 2900000>;
	qcom,vdd-current-level = <200 570000>;

	/* device communication power supply */
	vdd-io-supply = <&pm8953_l5>;
	qcom,vdd-io-always-on;
	qcom,vdd-io-lpm-sup;
	qcom,vdd-io-voltage-level = <1800000 1800000>;
	qcom,vdd-io-current-level = <200 325000>;

	pinctrl-names = "active", "sleep";
	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on  &sdc1_rclk_on>;
	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off &sdc1_rclk_off>;

	qcom,clk-rates = <400000 20000000 25000000 50000000 100000000 192000000
								384000000>;
	qcom,nonremovable;
	qcom,bus-speed-mode = "HS400_1p8v", "HS200_1p8v", "DDR_1p8v";

	status = "ok";
};

&sdhc_2 {
	/* device core power supply */
	vdd-supply = <&pm8953_l11>;
	qcom,vdd-voltage-level = <2950000 2950000>;
	qcom,vdd-current-level = <15000 800000>;

	/* device communication power supply */
	vdd-io-supply = <&pm8953_l12>;
	qcom,vdd-io-voltage-level = <1800000 2950000>;
	qcom,vdd-io-current-level = <200 22000>;

	pinctrl-names = "active", "sleep";
	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;

	#address-cells = <0>;
	interrupt-parent = <&sdhc_2>;
	interrupts = <0 1 2>;
	#interrupt-cells = <1>;
	interrupt-map-mask = <0xffffffff>;
	interrupt-map = <0 &intc 0 125 0
		1 &intc 0 221 0
		2 &tlmm 133 0>;
	interrupt-names = "hc_irq", "pwr_irq", "status_irq";
	cd-gpios = <&tlmm 133 0x1>;

	qcom,clk-rates = <400000 20000000 25000000 50000000 100000000
								200000000>;
	qcom,bus-speed-mode = "SDR12", "SDR25", "SDR50", "DDR50", "SDR104";

	status = "ok";
};

&pm8953_gpios {
	/* GPIO 2 (NFC_CLK_REQ) */
	gpio@c100 {
		qcom,mode = <0>;
		qcom,output-type = <0>;
		qcom,pull = <0>;
		qcom,vin-sel = <2>;
		qcom,out-strength = <3>;
		qcom,src-sel = <0>;
		qcom,master-en = <1>;
		status = "okay";
	};
};