# This file allows user to override the factory # defaults for the WLAN Driver # Enable IMPS or not gEnableImps=1 # Enable/Disable Idle Scan gEnableIdleScan=0 # Increase sleep duration (seconds) during IMPS # 0 implies no periodic wake up from IMPS. Periodic wakeup is # unnecessary if Idle Scan is disabled. gImpsModSleepTime=0 # Enable BMPS or not gEnableBmps=1 # Enable suspend or not # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter gEnableSuspend=3 # Phy Mode (auto, b, g, n, etc) # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only # 7 = 11b only 8 = 11ac only. gDot11Mode=0 # CSR Roaming Enable(1) Disable(0) gRoamingTime=0 # Assigned MAC Addresses - This will be used until NV items are in place # Each byte of MAC address is represented in Hex format as XX Intf0MacAddress=000AF58989FF Intf1MacAddress=000AF58989FE Intf2MacAddress=000AF58989FD Intf3MacAddress=000AF58989FC # UAPSD service interval for VO,VI, BE, BK traffic InfraUapsdVoSrvIntv=0 InfraUapsdViSrvIntv=0 InfraUapsdBeSrvIntv=0 InfraUapsdBkSrvIntv=0 # Flag to allow STA send AddTspec even when ACM is Off gAddTSWhenACMIsOff=1 # Make 1x1 the default antenna configuration gNumRxAnt=1 # Beacon filtering frequency (unit in beacon intervals) gNthBeaconFilter=50 # Enable WAPI or not # WAPIIsEnabled=0 # Flags to filter Mcast abd Bcast RX packets. # Value 0: No filtering, 1: Filter all Multicast. # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast McastBcastFilter=3 #Flag to enable HostARPOffload feature or not hostArpOffload=1 #Flag to enable TCPChkSumOffld feature or not gEnableTCPChkSumOffld=0 #Flag to enable HostNSOffload feature or not hostNSOffload=1 #Flag to enable IPChkSumOffld feature or not gEnableIPChecksumOffload=0 #SoftAP Related Parameters # AP MAc addr gAPMacAddr=000AF589dcab # 802.11n Protection flag gEnableApProt=1 #Enable OBSS protection gEnableApOBSSProt=1 #Enable/Disable UAPSD for SoftAP gEnableApUapsd=1 # Fixed Rate gFixedRate=0 # Maximum Tx power # gTxPowerCap=30 # Fragmentation Threshold # gFragmentationThreshold=2346 # RTS threshold RTSThreshold=1048576 # Intra-BSS forward gDisableIntraBssFwd=0 # WMM Enable/Disable WmmIsEnabled=0 # 802.11d support g11dSupportEnabled=0 # 802.11h support g11hSupportEnabled=1 # DFS Master Capability gEnableDFSMasterCap=1 # ESE Support and fast transition EseEnabled=0 ImplicitQosIsEnabled=0 gNeighborScanTimerPeriod=200 gNeighborLookupThreshold=76 gNeighborReassocThreshold=81 gNeighborScanChannelMinTime=20 gNeighborScanChannelMaxTime=30 gMaxNeighborReqTries=3 # Legacy (non-ESE, non-802.11r) Fast Roaming Support # To enable, set FastRoamEnabled=1 # To disable, set FastRoamEnabled=0 FastRoamEnabled=1 #Check if the AP to which we are roaming is better than current AP in terms of RSSI. #Checking is disabled if set to Zero.Otherwise it will use this value as to how better #the RSSI of the new/roamable AP should be for roaming RoamRssiDiff=3 # If the RSSI of any available candidate is better than currently associated # AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without # registering for reassoc threshold). # NOTE: Value of 0 means that we would register for reassoc threshold. gImmediateRoamRssiDiff=10 # To enable, set g0oamIntraBand=1 (Roaming within band) # To disable, set gRoamIntraBand=0 (Roaming across band) gRoamIntraBand=1 # SAP Country code # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. # Example # US Indoor, USI # Korea Outdoor, KRO # Japan without optional byte, JP # France without optional byte, FR #gAPCntryCode=USI #Short Guard Interval Enable/disable gShortGI20Mhz=1 gShortGI40Mhz=1 #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled gAPAutoShutOff=0 #Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec gWlanAutoShutdown = 0 # Listen Energy Detect Mode Configuration # Valid values 0-128 # 128 means disable Energy Detect feature # 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. # 10-128 are reserved. # The EDET threshold mapping is as follows in 3dB step: # 0 = -60 dBm # 1 = -63 dBm # 2 = -66 dBm # ... # 7 = -81 dBm # 8 = -84 dBm # 9 = -87 dBm # Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: # # Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. # gEnablePhyAgcListenMode=128 #Preferred band (both or 2.4 only or 5 only) BandCapability=1 #Beacon Early Termination (1 = enable the BET feature, 0 = disable) enableBeaconEarlyTermination=1 beaconEarlyTerminationWakeInterval=3 #Channel Bonding gChannelBondingMode5GHz=0 #Enable Keep alive with non-zero period value gStaKeepAlivePeriod = 30 #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). #For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) #For both active and power save clients. #Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. #If doesn't honor for 5 seconds then DUT remove client. #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on #11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. #Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period #where we send NULL frame. gApLinkMonitorPeriod = 30 gGoLinkMonitorPeriod = 10 #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. #Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. gGoKeepAlivePeriod = 3 gApKeepAlivePeriod = 20 #If set will start with active scan after driver load, otherwise will start with #passive scan to find out the domain gEnableBypass11d=1 #If set to 0, will not scan DFS channels gEnableDFSChnlScan=0 # Enable DFS channel roam # 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE gAllowDFSChannelRoam=0 gVhtChannelWidth=1 gEnableLogp=1 # Enable Automatic Tx Power control gEnableAutomaticTxPowerControl=1 # 0 for OLPC 1 for CLPC and SCPC gEnableCloseLoop=1 #Data Inactivity Timeout when in powersave (in ms) gDataInactivityTimeout=200 # Enable/disable 2x2 # 0 - 1x1 (default) # 1 - 2x2 gEnable2x2=1 # VHT Tx/Rx MCS values # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gVhtRxMCS=2 gVhtTxMCS=2 # VHT Tx/Rx MCS values for 2x2 # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gVhtRxMCS2x2=2 gVhtTxMCS2x2=2 # Valid chain mask values # 01 - enables chain0 # 02 - enables chain1 # 03 - enables both chain 0 and chain 1 # if set to 0 or 1 then all vdevs comes up in 1x1 mode in that band. gChainMask_2g=3 gChainMask_5g=3 # NSS cfg bit definition. # STA BIT[0:1] # SAP BIT[2:3] # P2P_GO BIT[4:5] # P2P_CLIENT BIT[6:7] # IBSS BIT[8:9] # TDLS BIT[10:11] # P2P_DEVICE BIT[12:13] # OCB BIT[14:15] # Valid values are 1 or 2 for each two bit configuration. # if 2-bit value is set to 1 then the corresponidng vdev comes up in 1x1 mode # in the band, if set to 2 then that vdev comes up in 2x2 mode in that band. gVdevTypeNss_2g=43690 gVdevTypeNss_5g=43690 # Scan Timing Parameters # gPassiveMaxChannelTime=110 # gPassiveMinChannelTime=60 gActiveMaxChannelTime=80 gActiveMinChannelTime=40 #If set to 0, MCC is not allowed. gEnableMCCMode=1 # MCC to SCC Switch mode: 0-Disable 1-Enable 2-Force SCC if same band gWlanMccToSccSwitchMode = 0 # 1=enable STBC; 0=disable STBC gEnableRXSTBC=1 # 1=enable tx STBC; 0=disable gEnableTXSTBC=1 # 1=enable rx LDPC; 0=disable gEnableRXLDPC=1 # 3=enable both HT/VHT TX LDPC # 2=enable VHT TX LDPC # 1=enable HT TX LDPC # 0=disable gTxLdpcEnable=3 #Enable/Disable Tx beamforming gTxBFEnable=0 # Enable Tx beamforming in VHT20MHz # Valid values are 0,1. If commented out, the default value is 0. # 0=disable, 1=enable gEnableTxBFin20MHz=0 # Enable Active mode offload gEnableActiveModeOffload=1 #Enable Scan Results Aging based on timer #Timer value is in seconds #If Set to 0 it will not enable the feature gScanAgingTime=0 #Enable Scan Results Aging based on number of scans gScanResultAgeCount=1 #Enable Power saving mechanism Based on Android Framework #If set to 0 Driver internally control the Power saving mechanism #If set to 1 Android Framwrok control the Power saving mechanism isAndroidPsEn=0 #Enable thermal mitigation gThermalMitigationEnable=0 #Thermal Mitigation Levels gThermalTempMinLevel0=0 gThermalTempMaxLevel0=107 gThermalTempMinLevel1=105 gThermalTempMaxLevel1=117 gThermalTempMinLevel2=110 gThermalTempMaxLevel2=127 gThermalTempMinLevel3=115 gThermalTempMaxLevel3=0 gEnableFastRoamInConcurrency=1 #List of Country codes for which 11ac needs to be disabled #Each country code must be delimited by comma(,) gListOfNon11acCountryCode=RU,UA,ZA #Maxium Channel time in msec gMaxMediumTime = 6000 # 802.11K support gRrmEnable=1 gRrmOperChanMax=8 gRrmNonOperChanMax=8 gRrmRandIntvl=100 #Scan offload gEnableDirectedScanOffload=1 #FlexConnect Power Factor #Default is set to 0 (disable) gFlexConnectPowerFactor=0 #Disable split scan, the FW will take care of it gNumChanCombinedConc=60 #Enable Power Save offload gEnablePowerSaveOffload=1 #Enable firmware uart print gEnablefwprint=0 #Enable firmware log gEnablefwlog=1 # Additional firmware log levels gFwDebugLogLevel=4 #IPA config gIPAConfig=0 gIPADescSize=800 gIPAPreFilterEnable=1 gIPARMEnable=1 gIPAIPv6Enable=1 #P2P Listen offload gEnableP2pListenOffload=1 # Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k) gVhtAmpduLenExponent=7 # Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets) gVhtMpduLen=2 # Maximum number of wow filters required #gMaxWoWFilters=22 # WOW Enable/Disable. # 0 - Disable both magic pattern match and pattern byte match. # 1 - Enable magic pattern match on all interfaces. # 2 - Enable pattern byte match on all interfaces. # 3 - Enable both magic patter and pattern byte match on all interfaces. # Default value of gEnableWoW is 3. # gEnableWoW=0 # Enable or Disable MCC Adaptive Scheduler at the FW # 1=Enable (default), 0=Disable gEnableMCCAdaptiveScheduler=1 #Enable or Disable p2p device address administered isP2pDeviceAddrAdministrated=1 # RX packet handling options # 0: no rx thread, no RPS, for MDM # 1: RX thread # 2: RPS rxhandle=0 # Set Thermal Power limit TxPower2g=10 TxPower5g=10 # Remove Overlap channel restriction gEnableOverLapCh=0 #Enable VHT on 2.4Ghz gEnableVhtFor24GHzBand=0 #Enable or Disable 5G early beacon termination gEnable5gEBT=0 #Maximum number of offload peers supported # gMaxOffloadPeers=2 # controlling the following offload patterns # through ini parameter. Default value is 1 # to disable set it to zero. ssdp = 0 # Setup multicast pattern for mDNS 224.0.0.251, # SSDP 239.255.255.250 and LLMNR 224.0.0.252 ssdp = 0 #Enable Memory Deep Sleep gEnableMemDeepSleep=1 #Disable packet log feature gEnablePacketLog=0 # Bus bandwidth threshold values in terms of number of packets gBusBandwidthHighThreshold=2000 gBusBandwidthMediumThreshold=500 gBusBandwidthLowThreshold=150 # Bus bandwidth compute timeout value in ms gBusBandwidthComputeInterval=100 # Regulatory Setting; 0=STRICT; 1=CUSTOM gRegulatoryChangeCountry=1 # RA filtering rate limit param, the current value would not # help if the lifetime in RA is less than 3*60=3min. Then # we need to change it, though it is uncommon. # gRAFilterEnable=0 gRArateLimitInterval=600 # Maximum number of concurrent connections gMaxConcurrentActiveSessions=2 # Disable/Enable GreenAP # 0 to disable, 1 to enable, default: 1 gEnableGreenAp=1 # Radar PRI multiplier gDFSradarMappingPriMultiplier=4 gPNOScanSupport=0 # Enable/Disable RX full reorder offload gReorderOffloadSupported=0 #Enable/Disable LPASS support # 0 to disable, 1 to enable gEnableLpassSupport=0 #Set SAP max peer to 16 which allows 10 WEP connection gSoftApMaxPeers=16 # Whether userspace country code setting shld have priority gCountryCodePriority=1 # Enable(1)/Disable(0) SIFS burst gEnableSifsBurst=1 # Enable or Disable Multi-user MIMO # 1=Enable (default), 0=Disable gEnableMuBformee=1 # Enable/Disable channel avoidance for SAP in SCC scenario # 0 - disable # 1 - enable gSapSccChanAvoidance=0 # Inactivity time (in ms) to end TX Service Period while in IBSS power save mode gIbssTxSpEndInactivityTime=10 # Enable/Disable Roaming Offload Support (a.k.a Key Management Offload) # 0 to disable, 1 to enable gRoamOffloadEnabled=0 # Enable or Disable Random MAC (Spoofing) # 1=Enable, 0=Disable (default) gEnableMacAddrSpoof=0 # Set SAP TX leakage threshold # The value should between 100 and 1000 # Default: 310 gsap_tx_leakage_threshold=400 # Support to start sap in indoor channel # Customer can config this item to enable/disable sap in indoor channel # Default: Enable gindoor_channel_support=1 # Enable broadcast logging to the userspace entities gMulticastHostFwMsgs=0 # Driver force 11AC override for SAP/Go gAP11ACOverride=0 # Enable EGAP gEnableEGAP=1 gEGAPInactTime=1000 gEGAPWaitTime=100 gEGAPFeatures=7 # Enable FW silent recovery under certain errors indicated gEnableSelfRecovery=1 END # Note: Configuration parser would not read anything past the END marker